Corrugated Veneer Panel Thermophysical Properties

Number of journal: 10-2024
Autors:

Galaktionov O.N.,
Suhanov Yu.V.,
Vasilyev A.S.,
Kuzmenkov A.A.

DOI: https://doi.org/10.31659/0585-430X-2024-829-10-68-74
УДК: 624.011.1

 

AbstractAbout AuthorsReferences
The article substantiates the need to develop new mechanisms for the hardwood use in modern conditions of Republic of Karelia timber industry. One of the potential uses of birch wood in wooden house construction is building materials production from veneer and slab materials based on it. A large amount of associated waste from processing birch wood into veneer stands out as one of the key problems. A new slab joinery and construction material made of corrugated birch veneer is considered. The purpose of this study is to evaluate the thermophysical properties of a corrugated board made of birch wood. To achieve this goal, the tasks and methods of research are defined. An experimental device has been developed to conduct an experiment to determine the values of thermophysical characteristics. DS18B20 temperature sensors were used to measure the surface temperature, as well as to monitor device operation and the room air temperature. The sensors are connected to the Arduino microcontroller platform, which was used to record and transmit sensor readings. Additionally, the course of the experiment was monitored using a thermal imager Testo 875-1i. During the experiment, more than 1000 measurements were carried out. As a result of data processing, a diagram of the dependence of the density of the heat flux passing through the sample on time, as well as diagrams of the dependence of thermal conductivity and thermal resistance on the temperature difference on the sample surfaces, was obtained. The diagrams show the regression dependences of changes in heat flux density, thermal conductivity and thermal resistance during measurements. The values of the heat flux density, thermal conductivity coefficient and thermal resistance calculated on the basis of regression equations and the values obtained experimentally are determined. The directions of further research of the material under consideration are determined.
O.N. GALAKTIONOV, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.),
Yu.V. SUHANOV, Candidate of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.),
A.S. VASILYEV, Candidate of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.),
A.A. KUZMENKOV, Candidate of Sciences (Economy), (This email address is being protected from spambots. You need JavaScript enabled to view it.)

State Architectural and Construction University (33, Lenin Street, Petrozavodsk, 185910, Russian Federation)

1. Galaktionov O., Vasiliev A., Sukhanov Y., Lukashevich V. Analysis of the forestry sector in the Republic of Karelia under current economic conditions. E3S Web of Conferences. 2023. Vol. 402, p. 13031. https://doi.org/10.1051/e3sconf/202340213031
2. Рогожина А.В. Развитие и анализ основных технологий малоэтажного строительства из материалов на основе древесины // Жилищное строительство. 2019. № 12. С. 35–39. https://doi.org/10.31659/0044-4472-2019-12-35-39
2. Rogozhina A.V. Development and analysis of the main technologies of low-rise construction of materials on the basis of wood. Zhilishchnoe stroitel’stvo [Housing Construction]. 2019. No. 12, pp. 35–39. (In Russian) https://doi.org/10.31659/0044-4472-2019-12-35-39
3. Kuzmenkov A., Galaktionov O., Karpov M., & Emelianova E. Wood raw materials and wood waste use for the building materials production (on the example of the Republic of Karelia timber industry). E3S Web of Conferences. 2023. Vol. 458, p. 07025. https://doi.org/10.1051/e3sconf/202345807025
4. Kuzmenkov A., Galaktionov O., Fedorova A., Emelianova E. Possibilities of using wood and wood materials in the construction of the Republic of Karelia. E3S Web of Conferences. 2023. Vol. 389, p. 01013. https://doi.org/10.1051/e3sconf/202338901013
5. Grinins J., Biziks V., Marais B.N., Rizikovs J., Militz H. Weathering stability and durability of birch plywood modified with different molecular weight phenol-formaldehyde oligomers. Polymers. 2021. Vol. 13. P. 175. https://doi.org/10.3390/polym13020175
6. Величко Е.Г., Цховребов Э.С. Экологическая безопасность строительных материалов: основные исторические этапы // Вестник МГСУ. 2017. Т. 12. Вып. 1 (100). С. 26–35. https://doi.org/10.22227/1997-0935.2017.1.26-35
6. Velichko E.G., Tskhovrebov E.S. Ecological safety of construction materials: basic historical stages. Vestnik MGSU. 2017. Vol. 12. Iss. 1 (100), pp. 26–35. (In Russian). https://doi.org/10.22227/1997-0935.2017.1.26-35
7. Mergel Ch., Menrad K., Decker T. Which factors influence consumers’ selection of wood as a building material for houses? Canadian Journal of Forest Research. e-First. 2024. https://doi.org/10.1139/cjfr-2023-01972024
8. Huang Y., Hu J., Peng H., Chen J., Wang Y., Zhu R., Yu W., Yahui Zh. A new type of engineered wood product: Cross-laminated-thick veneers. Case Studies in Construction Materials. 2023. Vol. 20, p. e02753. https://doi.org/20. 10.1016/j.cscm.2023.e02753
9. Joensuu T., Tuominen E., Vinha J., Saari A. Methodological aspects in assessing the whole-life global warming potential of wood-based building materials: Comparing exterior wall structures insulated with wood shavings. Environmental Research: Infrastructure and Sustainability. 2023. Vol. 3. Iss. 4. 045002. https://doi.org/10.1088/2634-4505/acfbaf
10. Pramreiter M., Nenning T., Huber Ch., Müller U., Kromoser B., Mayencourt P., Konnerth J. A review of the resource efficiency and mechanical performance of commercial wood-based building materials. Sustainable Materials and Technologies. 2023. Vol. 38, p. e00728. https://doi.org/10.1016/j.susmat.2023.e00728
11. Сусоева И.В., Вахнина Т.Н., Титунин А.А., Румянцева В.Е. Технологические факторы и свойства теплоизоляционных плит из растительных наполнителей // Известия высших учебных заведений. Лесной журнал. 2022. № 4 (388). С. 185–197. https://doi.org/10.37482/0536-1036-2022-4-185-197
11. Susoeva I.V., Vakhnina T.N., Titunin A.A., Rumyantseva V.E. Processing factors and properties of thermal insulation boards made of plant fillers Izvestiya of higher educational institutions. Forestry magazine. 2022. No. 4 (388), pp. 185–197. (In Russian). https://doi.org/10.37482/0536-1036-2022-4-185-197
12. Tobisch S., Dunky M., Hänsel A., Krug D., Wenderdel C. Survey of wood-based materials. Springer Handbook of Wood Science and Technology, pp. 1211–1282. https://doi.org/10.1007/978-3-030-81315-4_24
13. Karachentseva I., Kuzmenkov A., Kaychenov A., Voronin Z. Energy-efficient building materials for Arctic conditions as a criterion for “green building”. E3S Web of Conferences. 2023. Vol. 383. 04075. https://doi.org/10.1051/e3sconf/202338304075
14. Кузьменков А.А., Караченцева Я.М., Дербенёв А.В. Обоснование конструктивных и технологических решений экспериментального деревянного малоэтажного здания с учетом принципов «зеленого строительства» // Resources and Technology. 2021. Т. 18. № 1. С. 66–93. https://doi.org/10.15393/j2.art.2021.5522
14. Kuz’menkov A.A., Karachentseva Ya.M., Derbe-nev A.V. Substantiation of constructive and technological solutions for an experimental low-rise wooden house in accordance with the principles of «Green Building». Resources and Technology. 2021. Vol. 18. No. 1, pp. 66–93. (In Russian). https://doi.org/10.15393/j2.art.2021.5522
15. Kuzmenkov A.A., Kolesnikov G.N., Voronin Z.A., Green technologies of wooden building for Arctic. Lecture Notes in Civil Engineering. 2022. Vol. 227, pp. 385–398. https://doi.org/10.1007/978-3-030-94770-5_30
16. Бакатович А.А., Бакатович Н.В., Пенкрат А.Н. Фракционный состав измельченной сосновой коры и вид вяжущего компонента как основные факторы, влияющие на коэффициент тепло-проводности теплоизоляционных плит // Вестник Полоцкого государственного университета. Сер. F, Строительство. Прикладные науки. 2022. № 8. С. 38–45. https://doi.org/10.52928/2070-1683-2022-31-8-38-45
16. Bakatovich А.A., Bakatovich N.V., Penkrat A.N. The fractional composition of crushed pine bark and the type of binder component as the main factors affecting the thermal conductivity coefficient of thermal insulation plates. Vestnik of Polotsk State University. Series F. Construction. Applied Sciences. 2022. Vol. 31, pp. 38–45. https://doi.org/10.52928/2070-1683-2022-31-8-38-45
17. Buryachenko S., Voronin Z., Karachentseva I., Kuzmenkov A., Popova O. Factors influencing the rating of low-rise wooden houses as “green” buildings. E3S Web of Conferences. 2021. Vol. 263, p. 05018. https://doi.org/10.1051/e3sconf/202126305018
18. Buryachenko S.Y., Kuzmenkov A.A., Karachentseva I.M., Voronin Z.A., Popova O.M. Green building in the northern and Arctic regions. IOP Conference Series: Earth and Environmental Science. 2021. Vol. 937. No. 4, p. 042030. https://doi.org/10.1088/1755-1315/937/4/042030
19. Galactionov O.N., Sukhanov Y.V., Vasilev A.S., Kuzmenkov A.A., Kuznetsov A.V., Lukashevich V.M. Evaluation thermal insulation property of the corrugated veneer birch wood panel offered to use as a modern cladding material for interior decoration. Ad Alta: Journal of Interdisciplinary Research. 2023. Vol. 13. Iss. 2, pp. 357–360. https://doi.org/10.33543/1302.
20. Патент РФ на полезную модель RU 220698 U1. Панель гофрошпонная / Галактионов О.Н., Суханов Ю.В., Васильев А.С,, Васильев А.А., Потахин А.Г. Заявл. 22.05.2023. Опубл. 28.09.2023. Бюл. № 28.
20. The patent Russian Federation for a utility model RU 220698 U1. Panel’ gofroshponnaya [Corrugated panel].Galaktionov O.N., Sukhanov Yu.V., Vasil’ev A.S., Vasil’ev A.A., Potakhin A.G. Declared 22.05.2023. Published 28.09.2023. Bulletin No. 28. (In Russian).
21. Патент РФ на изобретение RU 2808051 C1. Способ изготовления панели гофрошпонной / Галактионов О.Н., Суханов Ю.В., Васильев А.С., Васильев А.А., Потахин А.Г. Заявл. 22.05.2023, Опубл. 22.11.2023. Бюл. № 33.
21. The patent of the Russian Federation for the invention RU 2808051 C1. Sposob izgotovleniya paneli gofroshponnoi [Method for manufacturing corrugated veneer panel]. Galaktionov O.N., Sukhanov Yu.V., Vasil’ev A.S., Vasil’ev A.A., Potakhin A.G. Declared 22.05.2023. Published 22.11.2023. Bulletin No. 33. (In Russian).
22. Пастушков П.П. О проблемах определения теплопроводности строительных материалов // Строительные материалы. 2019. № 4. С. 57–63. https://doi.org/10.31659/0585-430X-2019-769-4-57-63
22. Pastushkov P.P. On the problems of determining the thermal conductivity of building materials. Stroitel’nye Materialy [Construction Materials]. 2019. No. 4, pp. 57–63. (In Russian). https://doi.org/10.31659/0585-430X-2019-769-4-57-63
23. Kuzmenkov A., Karachentseva I. Refinement of thermal engineering calculations results taking into account actual materials characteristics. E3S Web of Conferences. 2023. Vol. 402, p. 07001. https://doi.org/10.1051/e3sconf/202340207001

For citation: Galaktionov O.N., Suhanov Yu.V., Vasilyev A.S., Kuzmenkov A.A. Corrugated veneer panel thermophysical properties. Stroitel'nye Materialy [Construction Materials]. 2024. No. 10, pp. 68–74. (In Russian). https://doi.org/10.31659/0585-430X-2024-829-10-68-74


Print   Email