AbstractAbout AuthorsReferences
Studies of the effect of complex additives on the setting time of Portland cement have been carried out. Alumina cement, natural gypsum and trepel (porous silica rock) were chosen as additives. To simulate the test results, an orthogonal second-order Box-Wilson composition plan was used. The cement setting time was determined in accordance with the methods given in GOST 310.3–76 (Russian standard). The results were presented in the form of surfaces of regression equations of the second level, describing the dependences of the beginning and end of cement setting on the content of complex additives. Over the course of the experiment, the results showed the compositions of composite binders with a maximum and minimum of the initial setting time and their final setting times. Based on a review of the literature and the data obtained, conclusions were drawn about the possible effect of the introduced additives on the setting time of the cement paste.
D.T.L. NGUYEN, graduate student (This email address is being protected from spambots. You need JavaScript enabled to view it.),
V.A. SHVETSOVA, head of laboratory (This email address is being protected from spambots. You need JavaScript enabled to view it.),
S.V. SAMCHENKO, Doctor of Sciences (Engineering), Professor (This email address is being protected from spambots. You need JavaScript enabled to view it.)
V.A. SHVETSOVA, head of laboratory (This email address is being protected from spambots. You need JavaScript enabled to view it.),
S.V. SAMCHENKO, Doctor of Sciences (Engineering), Professor (This email address is being protected from spambots. You need JavaScript enabled to view it.)
National Research Moscow State University of Civil Engineering (26, Yaroslavskoe Highway, Moscow, 129337, Russian Federation)
1. Erofeev V.T., Rodin A.I., Bikbaev R.R., Piksaikina A.A. Investigation of the properties of Portland cement with the active mineral additive based on trepel. Vestnik PGTU. 2019. No. 3, pp. 7–17. (In Russian). DOI: https://doi.org/10.25686/2542-114X.2019.3.7
2. Panesar D.K., Zhang R. Performance comparison of cement replacing materials in concrete: Limestone fillers and supplementary cementing materials – A review. Construction and Building Materials. 2020. Vol. 251. 118866. DOI: https://doi.org/10.1016/j.conbuildmat.2020.118866
3. Zemri C., Bouiadjra M.B. Comparison between physical – mechanical properties of mortar made with Portland cement (CEMI) and slag cement (CEMIII) subjected to elevated temperature. Case Studies in Construction Materials. 2020. Vol. 12. E00339. DOI: https://doi.org/10.1016/j.cscm.2020. e00339
4. Nguyen D.T.L., Samchenko S.V. The effect of complex additives on the properties of cement. XXIII International scientific – practical conference of students and young scientists “Chemistry and chemical technology in the XXI century” named after outstanding chemists Kulev L.P. and Kizhner N.M. 2022. Vol. 1, pp. 121–122. (In Russian).
5. Tang V.L., Nguyen D.T.L., Samchenko S.V. The influence of the addition of ash and slag waste on the properties of sulfoaluminate Portland cement. Vestnik MGSU. 2019. No. 8, pp. 991–1003. (In Russian). DOI: 10.22227/1997-0935.2019.8.991-1003
6. Ivashina M.A., Krivoborodov Yu.R. Use of waste industry in sulfoaluminate clinker technologies. XIII International Congress of Young Scientists in Chemistry and Chemical Technology (ICCT-2017). Advances in the field of chemistry and chemical technologies. 2017. Vol. XXXI. No. 1, pp. 22–24. (In Russian).
7. Тang V.L., Ngo X.H., Bulgakov B.I., Aleksandrova O.V., Larsen O.A., Orekhova A.Yu., Tyurina A.A. The use of ash and slag waste as additional cementing material. Vestnik BGTU named after V.G. Shukhov. 2018. No. 8, pp. 10–18. (In Russian). DOI: https://doi.org/10.12737/article_5b6d58455b5832.12667511.
8. Potapova E.N., Guseva T.V., Tikhonova I.O., Kanishev A.S., Kemp R.G. Cement production: Aspects of the resource efficiency enhancement and negative environmental impact reduction. Stroitel’nye Materialy [Construction Materials]. 2020. No. 9, pp. 15-20. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2020-784-9-15-20.
9. Bazhenov Yu.M. Tekhnologiya betona [Concrete technology]. Moscow: ASV. 2011. 524 p.
10. Guvalov A.A., Kuznetsova T.V., Abbasova S.I. Improving the efficiency of cement binders with the use of silica-containing modifier. Stroitel’nye Materialy [Construction Materials]. 2018. No. 11, pp. 56–59. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2018-765-11-56-59.
11. Uglyanitsa A.V., Duvarov V.B. Modification of cement concretes with the spent catalyst of the production caprolactam. Innovatsii i investitsii. 2019. No. 6, pp. 286–290. (In Russian).
12. Golik V.I., Razorenov Yu.I., Vagin V.S., Lyashenko V.I. Efficiency of mineral additives to binding component for making hardening mixtures at underground operations. Ferrous Metallurgy. Bulletin of Scientific, Technical and Economic Information. 2021. Vol. 77. No. 6, pp. 643–650. (In Russian). DOI: https://doi.org/10.32339/0135-5910-2021-6-643-650.
13. Kuznetsova T.V., Guvalov A.A., Abbasova S.I. Modifier based on zeolite-containing rocks for the cement composition manufacture. Tekhnika i tekhnologiya silikatov. 2016. Vol. 3. No. 1, pp. 22–24. (In Russian).
14. Gavshina O.V., Yashkina S.Yu., Yashkin A.N., Doroganov V.A., Moreva I.Yu. Study of the effect of particulate additives on the setting time and microstructure of high-alumina cement. Construction Materials and Products. 2018. Vol. 1. No. 4, pp. 30–37. (In Russian). DOI: https://doi.org/10.34031/2618-7183-2018-1-4-30-37.
15. Krivoborodov Yu. R., Kuznetsova T. V. Effect of plasticizer on the properties of aluminate cements. Sukhie stroitel’nye smesi. 2019. No. 5, pp. 8–10. (In Russian).
16. Kuznetsova T.V., Talaber I. Glinozemnistyi tsement [Alumina cement]. Moscow: Stroyizdat. 1988. 272 p.
17. Cantaluppi M., Marinoni N., Cella F., Bravo A., Cámara F., Borghini G., Kagan W. An insight on the effect of sodium and silicon on microstructure and crystallography of high alumina cements. Cement and Concrete Research. 2021. Vol. 148. 106533. DOI: https://doi.org/10.1016/j.cemconres.2021.106533
18. Tang V.L., Nguyen D.T.L. Pozzolanic activity of finely dispersed mineral components of various nature in Vietnam. Tekhnika i tekhnologiya silikatov [Technique and technology of silicates]. 2021. Vol. 28. No. 1, pp. 7–12. (In Russian).
19. Bektas, F., Bektas, B.A. Analyzing mix parameters in ASR concrete using response surface methodology. Construction and Building Materials. 2014. Vol. 66, pp. 299–305. DOI: https://doi.org/10.1016/j.conbuildmat.2014.05.055
20. Vu K.Z., Bazhenova S.I., Do M.Ch., Khoang M.T., Nguen V.Z., Nguyen D.T.L. Optimizing foam concrete mix proportions using the Box-Wilson experimental design. Inzhenernyi vestnik Dona. 2021. No. 5, pp. 606–620. (In Russian).
21. Nguyễn Minh Tuyển. Quy hoạch thực nghiệm [Experimental Planning]. Hanoi: NXB Khoa học và Kỹ thuật. 2007. 264 p. (In Vietnamese).
22. Tang V.L., Ngo X.H., Vu K.D., Bulgakov B.I. Influence of a complex organo-mineral additive on the deformation of hydrotechnical concrete. Stroitel’stvo unikal’nykh zdanii i sooruzhenii. 2019. No. 4, pp. 7–19. (In Russian).
2. Panesar D.K., Zhang R. Performance comparison of cement replacing materials in concrete: Limestone fillers and supplementary cementing materials – A review. Construction and Building Materials. 2020. Vol. 251. 118866. DOI: https://doi.org/10.1016/j.conbuildmat.2020.118866
3. Zemri C., Bouiadjra M.B. Comparison between physical – mechanical properties of mortar made with Portland cement (CEMI) and slag cement (CEMIII) subjected to elevated temperature. Case Studies in Construction Materials. 2020. Vol. 12. E00339. DOI: https://doi.org/10.1016/j.cscm.2020. e00339
4. Nguyen D.T.L., Samchenko S.V. The effect of complex additives on the properties of cement. XXIII International scientific – practical conference of students and young scientists “Chemistry and chemical technology in the XXI century” named after outstanding chemists Kulev L.P. and Kizhner N.M. 2022. Vol. 1, pp. 121–122. (In Russian).
5. Tang V.L., Nguyen D.T.L., Samchenko S.V. The influence of the addition of ash and slag waste on the properties of sulfoaluminate Portland cement. Vestnik MGSU. 2019. No. 8, pp. 991–1003. (In Russian). DOI: 10.22227/1997-0935.2019.8.991-1003
6. Ivashina M.A., Krivoborodov Yu.R. Use of waste industry in sulfoaluminate clinker technologies. XIII International Congress of Young Scientists in Chemistry and Chemical Technology (ICCT-2017). Advances in the field of chemistry and chemical technologies. 2017. Vol. XXXI. No. 1, pp. 22–24. (In Russian).
7. Тang V.L., Ngo X.H., Bulgakov B.I., Aleksandrova O.V., Larsen O.A., Orekhova A.Yu., Tyurina A.A. The use of ash and slag waste as additional cementing material. Vestnik BGTU named after V.G. Shukhov. 2018. No. 8, pp. 10–18. (In Russian). DOI: https://doi.org/10.12737/article_5b6d58455b5832.12667511.
8. Potapova E.N., Guseva T.V., Tikhonova I.O., Kanishev A.S., Kemp R.G. Cement production: Aspects of the resource efficiency enhancement and negative environmental impact reduction. Stroitel’nye Materialy [Construction Materials]. 2020. No. 9, pp. 15-20. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2020-784-9-15-20.
9. Bazhenov Yu.M. Tekhnologiya betona [Concrete technology]. Moscow: ASV. 2011. 524 p.
10. Guvalov A.A., Kuznetsova T.V., Abbasova S.I. Improving the efficiency of cement binders with the use of silica-containing modifier. Stroitel’nye Materialy [Construction Materials]. 2018. No. 11, pp. 56–59. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2018-765-11-56-59.
11. Uglyanitsa A.V., Duvarov V.B. Modification of cement concretes with the spent catalyst of the production caprolactam. Innovatsii i investitsii. 2019. No. 6, pp. 286–290. (In Russian).
12. Golik V.I., Razorenov Yu.I., Vagin V.S., Lyashenko V.I. Efficiency of mineral additives to binding component for making hardening mixtures at underground operations. Ferrous Metallurgy. Bulletin of Scientific, Technical and Economic Information. 2021. Vol. 77. No. 6, pp. 643–650. (In Russian). DOI: https://doi.org/10.32339/0135-5910-2021-6-643-650.
13. Kuznetsova T.V., Guvalov A.A., Abbasova S.I. Modifier based on zeolite-containing rocks for the cement composition manufacture. Tekhnika i tekhnologiya silikatov. 2016. Vol. 3. No. 1, pp. 22–24. (In Russian).
14. Gavshina O.V., Yashkina S.Yu., Yashkin A.N., Doroganov V.A., Moreva I.Yu. Study of the effect of particulate additives on the setting time and microstructure of high-alumina cement. Construction Materials and Products. 2018. Vol. 1. No. 4, pp. 30–37. (In Russian). DOI: https://doi.org/10.34031/2618-7183-2018-1-4-30-37.
15. Krivoborodov Yu. R., Kuznetsova T. V. Effect of plasticizer on the properties of aluminate cements. Sukhie stroitel’nye smesi. 2019. No. 5, pp. 8–10. (In Russian).
16. Kuznetsova T.V., Talaber I. Glinozemnistyi tsement [Alumina cement]. Moscow: Stroyizdat. 1988. 272 p.
17. Cantaluppi M., Marinoni N., Cella F., Bravo A., Cámara F., Borghini G., Kagan W. An insight on the effect of sodium and silicon on microstructure and crystallography of high alumina cements. Cement and Concrete Research. 2021. Vol. 148. 106533. DOI: https://doi.org/10.1016/j.cemconres.2021.106533
18. Tang V.L., Nguyen D.T.L. Pozzolanic activity of finely dispersed mineral components of various nature in Vietnam. Tekhnika i tekhnologiya silikatov [Technique and technology of silicates]. 2021. Vol. 28. No. 1, pp. 7–12. (In Russian).
19. Bektas, F., Bektas, B.A. Analyzing mix parameters in ASR concrete using response surface methodology. Construction and Building Materials. 2014. Vol. 66, pp. 299–305. DOI: https://doi.org/10.1016/j.conbuildmat.2014.05.055
20. Vu K.Z., Bazhenova S.I., Do M.Ch., Khoang M.T., Nguen V.Z., Nguyen D.T.L. Optimizing foam concrete mix proportions using the Box-Wilson experimental design. Inzhenernyi vestnik Dona. 2021. No. 5, pp. 606–620. (In Russian).
21. Nguyễn Minh Tuyển. Quy hoạch thực nghiệm [Experimental Planning]. Hanoi: NXB Khoa học và Kỹ thuật. 2007. 264 p. (In Vietnamese).
22. Tang V.L., Ngo X.H., Vu K.D., Bulgakov B.I. Influence of a complex organo-mineral additive on the deformation of hydrotechnical concrete. Stroitel’stvo unikal’nykh zdanii i sooruzhenii. 2019. No. 4, pp. 7–19. (In Russian).
For citation: Nguyen D.T.L., Shvetsova V.A., Samchenko S.V. The influences of complex additives based on alumina cement on the properties of Portland cement. Stroitel’nye Materialy [Construction Materials]. 2023. No. 4, pp. 65–72. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2023-812-4-65-72