AbstractAbout AuthorsReferences
The dependence of the physical and mechanical properties of the composition on the basis of high-strength anhydrite binder on the concentration of light filler, as which the expanded perlite sand was used, was studied. The optimal ratio of filler and binder is determined by the combination of three main parameters: the compressive strength of the sample, the average density and the thermal conductivity coefficient. The assessment of the influence of the use of three modifying components: air-entraining admixture, primer with nano-additive and wetting agent on the physical and mechanical characteristics of the composition is carried out. Studies have shown that a significant impact on the properties of the composition had the introduction of an air entraining admixture, which increased the compressive strength at the age of 7 days from 1.34 to 2.07 MPa, as well as a wetting agent, which made it possible to reduce the density of the material from 891 to 695 kg/m3. The fluoro-anhydrite composition developed with a light filler on the basis of expanded perlite sand, with due regard for its physical and mechanical characteristics, can be used as an effective structural and thermal insulation material in the production of tongue-and-groove slabs, blocks for the construction of structures inside buildings and structures.
G.I. YAKOVLEV1, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
D.A. KALABINA1, graduate student (This email address is being protected from spambots. You need JavaScript enabled to view it.)
V.P. GRAKHOV1, Doctor of Sciences (Economics) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
A.F. BURYANOV2, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
A.F. GORDINA1, Candidate of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
K.A. BAZHENOV1, Student (This email address is being protected from spambots. You need JavaScript enabled to view it.)
S.V. NIKITINA3, Engineer (This email address is being protected from spambots. You need JavaScript enabled to view it.)
D.A. KALABINA1, graduate student (This email address is being protected from spambots. You need JavaScript enabled to view it.)
V.P. GRAKHOV1, Doctor of Sciences (Economics) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
A.F. BURYANOV2, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
A.F. GORDINA1, Candidate of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
K.A. BAZHENOV1, Student (This email address is being protected from spambots. You need JavaScript enabled to view it.)
S.V. NIKITINA3, Engineer (This email address is being protected from spambots. You need JavaScript enabled to view it.)
1 Kalashnikov Izhevsk State Technical University (7, Studencheskaya Street, Izhevsk, 426069, Russian Federation)
2 National Research Moscow State University of Civil Engineering (26, Yaroslavskoe Highway, Moscow, 129337, Russian Federation)
3 “Novi Dom” OOO (31, Salutovskaya Street, Izhevsk, 426053, Russian Federation)
1. Degirmenci N. Utilization of phosphogypsum as raw and calcined material in manufacturing of building products. Construction and Building Materials. 2008. Vol. 22, pp. 1857–1862. DOI: 10.1016/j.conbuildmat.2007.04.024
2. Гриневич А.В., Киселев А.А., Кузнецов Е.М., Бурьянов А.Ф., Ряшко А.И. Гипсовое вяжущее из α-СаSO4.0,5Н2О – отхода производства экстракционной фосфорной кислоты // Строительные материалы. 2014. № 7. C. 4–8.
2. Grinevich A.V., Kiselev A.A., Kuznetsov E.M., Bur’yanov A.F., Ryashko A.I. Gypsum binder from α-СаSO4.0,5Н2О – waste of extraction phosphoric acid production. Stroitel’nye Materialy [Construction Materials]. 2014. No. 7, pp. 4–8. (In Russian).
3. Garg M, Jain N, Singh M. Development of alpha plaster from phosphogypsum for cementitious binders. Construction and Building Materials. 2009. Vol. 23 (10), pp. 3138–3143. DOI: 10.1016/j.conbuildmat.2009.06.024
4. Орешкин Д.В. Экологические проблемы комплексного освоения недр при масштабной утилизации техногенных минеральных ресурсов и отходов в производстве строительных материалов // Строительные материалы. 2017. № 8. C. 55–63.
4. Oreshkin D.V. Environmental problems of comprehensive exploitation of mineral resources when largescale utilization of manmade mineral resources and waste in the production of building materials. Stroitel’nye Materialy [Construction Materials]. 2017. No. 8, pp. 55–63. DOI: https://doi.org/10.31659/0585-430X-2017-751-8-55-63 (In Russian).
5. Hughes P., Glendinning S. Deep dry mix ground improvement of a soft peaty clay using blast furnace slag and red gypsum. Quarterly Journal of Engineering Geology and Hydrogeology. 2004. Vol. 37 (3), pp. 205–216. DOI: 10.1144/1470-9236/04-003
6. Fauziah I., Zauyah S., Jamal T. Characterization and land application of red gypsum: a waste product from the titanium dioxide industry. Science of Total Environment. 1996. Vol. 188, pp. 243–251. DOI: 10.1016/0048-9697(96)05179-0
7. Tesárek Pavel, Drchalová Jaroslava, Kolísko Jiří, Rovnaníková Pavla, Černý Robert. Flue gas desulfurization gypsum: study of basic mechanical, hydric and thermal properties. Construction and Building Materials. 2007. Vol. 21, pp. 1500–1509. DOI: 10.1016/j.conbuildmat.2006.05.009
8. Xiao Lu Guo, Hui Sheng Shi Thermal treatment and utilization of flue gas desulphurization gypsum as an admixture in cement and concrete. Construction and Building Materials. 2008. Vol. 22, pp. 1471–1476. DOI: 10.1016/j.conbuildmat.2007.04.001
9. Tesárek P., Rovnaníková P., Kolísko J. Černý, R. Właściwości hydrofobowego gipsu z odsiarczania spalin [Properties of hydrophobized FGD gypsum]. Cement-wapno-beton. 2005. Vol. 5, pр. 255–264 (In Polish)|
10. Гордина А.Ф., Яковлев Г.И., Полянских И.С., Керене Я., Фишер Х.Б., Рахимова Н.Р., Бурьянов А.Ф. Гипсовые композиции с комплексными модификаторами структуры // Строительные материалы. 2016. № 1–2. C. 90–95.
10. Gordina A.F., Yakovlev G.I., Polyanskikh I.S., Kerene Ya., Fisher Kh.B., Rakhimova N.R., Bur’yanov A.F. Gypsum compositions with complex modifiers of structure. Stroitel’nye Materialy [Construction Materials]. 2016. No. 1–2, pp. 90–95. https://doi.org/10.31659/0585-430X-2016-733-734-1-2-90-95
11. Colak A. Density and strength characteristics of foamed gypsum. Cement & Concrete Composites. 2000. Vol. 22, pp. 193–200.
12. Skujans J., Vulans A., Iljins U., Aboltins A. Measurements of heat transfer of multi-layered wall construction with foam gypsum. Applied Thermal Engineering. 2007. Vol. 27, pp. 1219–1224. DOI: 10.1016/j.applthermaleng.2006.02.047
13. Sayil B., Gurdal E. The physical properties of polystyrene aggregated gypsum blocks. Edited by Lacasse M.A., Vainer D.J. Proceedings of 8th international conference on durability of building materials and components. Canada: Vancouver. 1999, pp. 496–504 http://www.irbnet.de/daten/iconda/CIB1966.pdf
14. Santos A.G. PPF-reinforced, ESP-lightened gypsum plaster. Materiales de Construccion. 2009. Vol. 59, pp. 105–124. https://doi.org/10.3989/mc.2009.41107
15. Vimmrová Alena, Keppert Martin, Svoboda Luboš, Černý Robert. Lightweight gypsum composites: Design strategies for multi-functionality. Cement and Concrete Composites. 2011. Vol. 33, Iss. 1, pp. 84–89. https://doi.org/10.1016/j.cemconcomp.2010.09.011
16. Svoboda L., Vimmrová A. Acid agent for preparation of foamed gypsum. Czech utility design no. 17844. Prague. 2007.
17. Yakovlev G.I.,Tulegenova A.V., Pervushin G.N., Keriene J., Gordina A.F., Bazhenov K.A., Ali Elsayed Elrefaei. Multifunctional admixture used for activating fluoroanhydrite. 20th International Building Materials Conference «Ibausil». 12–14 September 2018. Weimar, Germany. Band 2, pp. 559–568.
18. Яковлев Г.И., Первушин Г.Н., Грахов В.П., Калабина Д.А., Гордина А.Ф., Гинчицкая Ю.Н., Баженов К.А., Трошкова В.В., Дрохитка Р., Хозин В.Г. Конструкционно-теплоизоляционный материал на основе высокопрочного ангидритового вяжущего // Интеллектуальные системы в производстве. 2019. Т. 17. № 1. С. 144–151. DOI: 10.22213/2410-9304-2019-1-144-151
18. Yakovlev G.I., Pervushin G.N., Grakhov V.P., Kalabina D.A., Gordina A.F., Ginchitskaya Yu.N., Bazhenov K.A., Troshkova V.V., Drokhitka R., Khozin V.G. Constructional and thermal insulation material based on high-strength anhydrite binder. Intellektual’nye sistemy v proizvodstve. 2019. Vol. 17. No. 1, pp. 144–151. DOI: 10.22213/2410-9304-2019-1-144-151 (In Russian).
2. Гриневич А.В., Киселев А.А., Кузнецов Е.М., Бурьянов А.Ф., Ряшко А.И. Гипсовое вяжущее из α-СаSO4.0,5Н2О – отхода производства экстракционной фосфорной кислоты // Строительные материалы. 2014. № 7. C. 4–8.
2. Grinevich A.V., Kiselev A.A., Kuznetsov E.M., Bur’yanov A.F., Ryashko A.I. Gypsum binder from α-СаSO4.0,5Н2О – waste of extraction phosphoric acid production. Stroitel’nye Materialy [Construction Materials]. 2014. No. 7, pp. 4–8. (In Russian).
3. Garg M, Jain N, Singh M. Development of alpha plaster from phosphogypsum for cementitious binders. Construction and Building Materials. 2009. Vol. 23 (10), pp. 3138–3143. DOI: 10.1016/j.conbuildmat.2009.06.024
4. Орешкин Д.В. Экологические проблемы комплексного освоения недр при масштабной утилизации техногенных минеральных ресурсов и отходов в производстве строительных материалов // Строительные материалы. 2017. № 8. C. 55–63.
4. Oreshkin D.V. Environmental problems of comprehensive exploitation of mineral resources when largescale utilization of manmade mineral resources and waste in the production of building materials. Stroitel’nye Materialy [Construction Materials]. 2017. No. 8, pp. 55–63. DOI: https://doi.org/10.31659/0585-430X-2017-751-8-55-63 (In Russian).
5. Hughes P., Glendinning S. Deep dry mix ground improvement of a soft peaty clay using blast furnace slag and red gypsum. Quarterly Journal of Engineering Geology and Hydrogeology. 2004. Vol. 37 (3), pp. 205–216. DOI: 10.1144/1470-9236/04-003
6. Fauziah I., Zauyah S., Jamal T. Characterization and land application of red gypsum: a waste product from the titanium dioxide industry. Science of Total Environment. 1996. Vol. 188, pp. 243–251. DOI: 10.1016/0048-9697(96)05179-0
7. Tesárek Pavel, Drchalová Jaroslava, Kolísko Jiří, Rovnaníková Pavla, Černý Robert. Flue gas desulfurization gypsum: study of basic mechanical, hydric and thermal properties. Construction and Building Materials. 2007. Vol. 21, pp. 1500–1509. DOI: 10.1016/j.conbuildmat.2006.05.009
8. Xiao Lu Guo, Hui Sheng Shi Thermal treatment and utilization of flue gas desulphurization gypsum as an admixture in cement and concrete. Construction and Building Materials. 2008. Vol. 22, pp. 1471–1476. DOI: 10.1016/j.conbuildmat.2007.04.001
9. Tesárek P., Rovnaníková P., Kolísko J. Černý, R. Właściwości hydrofobowego gipsu z odsiarczania spalin [Properties of hydrophobized FGD gypsum]. Cement-wapno-beton. 2005. Vol. 5, pр. 255–264 (In Polish)|
10. Гордина А.Ф., Яковлев Г.И., Полянских И.С., Керене Я., Фишер Х.Б., Рахимова Н.Р., Бурьянов А.Ф. Гипсовые композиции с комплексными модификаторами структуры // Строительные материалы. 2016. № 1–2. C. 90–95.
10. Gordina A.F., Yakovlev G.I., Polyanskikh I.S., Kerene Ya., Fisher Kh.B., Rakhimova N.R., Bur’yanov A.F. Gypsum compositions with complex modifiers of structure. Stroitel’nye Materialy [Construction Materials]. 2016. No. 1–2, pp. 90–95. https://doi.org/10.31659/0585-430X-2016-733-734-1-2-90-95
11. Colak A. Density and strength characteristics of foamed gypsum. Cement & Concrete Composites. 2000. Vol. 22, pp. 193–200.
12. Skujans J., Vulans A., Iljins U., Aboltins A. Measurements of heat transfer of multi-layered wall construction with foam gypsum. Applied Thermal Engineering. 2007. Vol. 27, pp. 1219–1224. DOI: 10.1016/j.applthermaleng.2006.02.047
13. Sayil B., Gurdal E. The physical properties of polystyrene aggregated gypsum blocks. Edited by Lacasse M.A., Vainer D.J. Proceedings of 8th international conference on durability of building materials and components. Canada: Vancouver. 1999, pp. 496–504 http://www.irbnet.de/daten/iconda/CIB1966.pdf
14. Santos A.G. PPF-reinforced, ESP-lightened gypsum plaster. Materiales de Construccion. 2009. Vol. 59, pp. 105–124. https://doi.org/10.3989/mc.2009.41107
15. Vimmrová Alena, Keppert Martin, Svoboda Luboš, Černý Robert. Lightweight gypsum composites: Design strategies for multi-functionality. Cement and Concrete Composites. 2011. Vol. 33, Iss. 1, pp. 84–89. https://doi.org/10.1016/j.cemconcomp.2010.09.011
16. Svoboda L., Vimmrová A. Acid agent for preparation of foamed gypsum. Czech utility design no. 17844. Prague. 2007.
17. Yakovlev G.I.,Tulegenova A.V., Pervushin G.N., Keriene J., Gordina A.F., Bazhenov K.A., Ali Elsayed Elrefaei. Multifunctional admixture used for activating fluoroanhydrite. 20th International Building Materials Conference «Ibausil». 12–14 September 2018. Weimar, Germany. Band 2, pp. 559–568.
18. Яковлев Г.И., Первушин Г.Н., Грахов В.П., Калабина Д.А., Гордина А.Ф., Гинчицкая Ю.Н., Баженов К.А., Трошкова В.В., Дрохитка Р., Хозин В.Г. Конструкционно-теплоизоляционный материал на основе высокопрочного ангидритового вяжущего // Интеллектуальные системы в производстве. 2019. Т. 17. № 1. С. 144–151. DOI: 10.22213/2410-9304-2019-1-144-151
18. Yakovlev G.I., Pervushin G.N., Grakhov V.P., Kalabina D.A., Gordina A.F., Ginchitskaya Yu.N., Bazhenov K.A., Troshkova V.V., Drokhitka R., Khozin V.G. Constructional and thermal insulation material based on high-strength anhydrite binder. Intellektual’nye sistemy v proizvodstve. 2019. Vol. 17. No. 1, pp. 144–151. DOI: 10.22213/2410-9304-2019-1-144-151 (In Russian).
For citation: Yakovlev G.I., Kalabina D.A., Grakhov V.P., Buryanov A.F., Gordina A.F., Bazhenov K.A., Nikitina S.V. Fluoro-anhydrite compositions with a light filler based on expanded perlite sand. Stroitel’nye Materialy [Construction Materials]. 2019. No. 5, pp. 57–61. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2019-770-5-57-61